1 copyright ? 2010, everlight america s inc . all ri ghts reserved. release date : may . 05 .201 4 . issue no: xxxxxxxxxx rev.0.1 www.everlightamericas.com technical data sheet 1.6mm round subminiature side looking infrared led EAIST3216A2 features ? small double - end package ? low forward voltage ? good spectral matching to si photo detector ? pack age in 8 mm tape on 7 diameter reel. ? pb free ? the product itself will remain within rohs compliant version. ? compliance with eu reach. ? compliance halogen free .(br <900 ppm ,cl <900 ppm , br+cl < 1500 ppm) description ? EAIST3216A2 is an infrared emitting diode in miniature smd package which is molded in a water clear plastic with spherical top view lens. the device is spectrally matched with silicon photodiode and phototransistor . applications ? pcb mounted infrared sensor ? infrared em itting for miniature light barrier ? floppy disk drive ? optoelectronic switch ? smoke detector device selection guide device no. chip material lens color EAIST3216A2 gaalas water clear
datasheet EAIST3216A2 2 copyright ? 2010, everlight americas inc . all ri ghts reserved. release date : may . 05 .201 4 . issue no: xxxxxxxxxx rev.0.1 www.everlightamericas.com package dimensions notes: 1.all dimensions are in millimeters 2.tolerances unless dimensions 0.1mm absolute maximum ratings (ta=25 parameter symbol rating unit continuous forward current i f 65 ma reverse voltage v r 5 v operating temperature t opr - 25 ~ +85 stg - 40 ~ + 100 sol 260 d 130 mw notes: *1:soldering time Q recommended soldering pattern for side looker
datasheet EAIST3216A2 3 copyright ? 2010, everlight americas inc . all ri ghts reserved. release date : may . 05 .201 4 . issue no: xxxxxxxxxx rev.0.1 www.everlightamericas.com electro - optical charac teristics (ta=25 ) rankings rank test condition min max unit h i f =20ma 2.0 3.5 mw/sr j 3.0 4.5 k 4.0 6.0 l 5.0 7.5 m 6.0 9.0 n 7.0 10.5 parameter symbol min. typ. max. unit condition radiant intensity i e 2 .0 4 .5 -- mw /sr i f =20ma -- 15 -- i f =100ma pulse width Q 100 s ,duty Q 1% peak wavelength p -- 940 -- nm i f =20ma spectral bandwidth ? -- 45 -- nm i f =2 0ma forward voltage v f -- 1.2 1.5 v i f =20ma -- 1.5 1.8 i f =100ma pulse width Q 100 s ,duty Q 1% reverse current i r -- -- 10 a v r =5v view angle 2 1/2 -- 20 -- deg i f =20ma
datasheet EAIST3216A2 4 copyright ? 2010, everlight americas inc . all ri ghts reserved. release date : may . 05 .201 4 . issue no: xxxxxxxxxx rev.0.1 www.everlightamericas.com typical electrical/optical/characteristics curves forward current vs. ambient temperature spectral distribution peak emission wavelength vs. ambient temperature for ward current vs. forward voltage 0 -25 0 40 20 60 100 80 20 40 60 100 80 120 140 0 20 40 60 80 100 i f =20ma ta=25 c 75 -25 900 0 920 940 25 50 960 980 100 0 10 10 1 10 2 3 10 4 1 2 3 4
datasheet EAIST3216A2 5 copyright ? 2010, everlight americas inc . all ri ghts reserved. release date : may . 05 .201 4 . issue no: xxxxxxxxxx rev.0.1 www.everlightamericas.com relative intensity vs forward current relative radiant intensity vs. angular displacement i f -forward current (ma ) 10 10 0 10 1 10 2 3 10 4 ie-radiant intensity(mw/sr) 10 0 100 1000 -20 0.6 0.9 0.7 0.8 1.0 0.2 0.4 0 0.2 0.4 0.6 50 70 80 60 40 30 -10 0 20 10
datasheet EAIST3216A2 6 copyright ? 2010, everlight americas inc . all ri ghts reserved. release date : may . 05 .201 4 . issue no: xxxxxxxxxx rev.0.1 www.everlightamericas.com ? precautions for use 1. over - current - proof customer must apply resistors for protecti on , otherwise slight voltage shift will cause big current change ( burn out will happen ). 2. storage 2.1 do not open moisture proof bag before the products are ready to use. 2.2 before opening the package, the leds should be kept at 30 or l ess and 90%rh or less. 2. 3 the leds should be used within a year. 2. 4 after opening the package, the leds should be kept at 30 or less and 6 0%rh or less. 2.5 the leds should be used within 168 hours (7 days) after opening the package 2.6 if the moisture absorbent mate rial (silica gel) has faded away or the leds have exceeded the storage time, baking treatment should be performed using the following conditions. baking treatment : 60 5 for min. 24 hours. 3. soldering condition 3.1 pb - free solder temperature profile 3.2 reflow soldering should not be done more than two times. 3.3 when soldering, do not put stress on the leds during heating. 3.4 after soldering, do not warp the circuit board.
datasheet EAIST3216A2 7 copyright ? 2010, everlight americas inc . all ri ghts reserved. release date : may . 05 .201 4 . issue no: xxxxxxxxxx rev.0.1 www.everlightamericas.com 4. soldering iron each terminal i s to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25w. leave two seconds and more intervals, and do soldering of each terminal. be careful because the damage of the product is often started at the time of the hand solder. 5. repairing repair should not be done after the leds have been soldered. when repairing is unavoidable, a double - head soldering iron should be used (as below figure). it should be confirmed beforehand whet her the characteristics of the leds will or will not be damaged by repairing.
datasheet EAIST3216A2 8 copyright ? 2010, everlight americas inc . all ri ghts reserved. release date : may . 05 .201 4 . issue no: xxxxxxxxxx rev.0.1 www.everlightamericas.com package dimensions note: the tolerances unless mentioned is 0.1mm ,unit = mm 2. carrier tape dimensions: (q uantity : 15 00 pcs/ reel ) note: the tolerances unless mentioned is 0.1mm ,unit = mm anode
datasheet EAIST3216A2 9 copyright ? 2010, everlight americas inc . all ri ghts reserved. release date : may . 05 .201 4 . issue no: xxxxxxxxxx rev.0.1 www.everlightamericas.com packing procedure label form specification cpn: customers production number p/n : production number qty: packing quantity cat: ranks hue: peak wavelength ref: reference lot no: lot number made in taiwan: production place notes 1. above specification may be changed without notice. everlight americas will reserve authority on material change for above specification. 2. when using this product, please observe the abs olute maximum ratings and the instructions for using outlined in these specification sheets. everlight americas assumes no responsibility for any damage resulting from use of the product which does not comp ly with the absolute maximum ratings and the instr uctions included in these specification sheets. 3. these specification sheets include materials protected under copyright of everlight americas corporation. please dont reproduce or cause anyone to reproduce them without everlight americass consent. aluminum moistue-proof bag label desiccant label
|
